Hardwood Floor Refinishing in Union City, NJ
Hardwood Floor Refinishing for homes in Union City, Hudson County.
- 1958 median year built
- 70.2% built before 1978
- 27,442 housing units
- Hudson County
The median Union City home dates to 1958, and about 70.2% of the housing stock predates 1978 — which shapes what is under the finish and how the work has to be done.
What Union City floors are usually made of
With a median build year of 1958 and 33.2% of homes predating 1940, Union City has a genuinely mixed housing stock — which means the floor has to be identified before the work is scoped.
A mixed-era town is the hardest one to generalise about. Two houses on the same street in Union City can have completely different floors under the finish: original narrow board in one, postwar red oak strip in the other.
We do not assume. Wear layer, board width and species get checked on site, because the answer changes the method and the price.
How Union City compares
Housing here runs about 5 years older than the Hudson County median of 1963.
At 70.2% pre-1978, Union City sits in the older half of the 185 towns we serve. Neighbouring Hoboken is a different picture — median 1975 against 1958 here — which is why we quote by address rather than by area. Union City is about 33 miles from our base in Eatontown.
Housing data for Union City
These are the Census figures behind everything above — published so you can check them rather than take our word for it.
| Median year built | 1958 |
|---|---|
| Built before 1978 (approx.) | 70.2% |
| Built before 1940 | 33.2% |
| Housing units | 27,442 |
| Population | 66,375 |
| County | Hudson County |
Source: US Census Bureau, ACS 2023 5-Year Estimates. The pre-1978 share is an approximation — see how it is derived.
Lead-safe requirements in Union City
About 70.2% of Union City homes were built before 1978, so work that disturbs painted baseboards, shoe molding or stair components will usually fall under the EPA's lead-safe rule.
This is the normal condition of a Union City job, not an exception to plan around. The exposure is at the edges of the floor — sanding equipment runs directly against painted trim.
Dust containment and lead-safe practice are different things. A containment system manages nuisance dust; the RRP rule addresses a regulated hazard and carries its own containment, cleaning and verification requirements. Ask about both, separately.
The pre-1978 figure is approximate — see the method note on our housing data page for how it is derived.
Hardwood Floor Refinishing, in short
Refinishing sands a wood floor back to bare wood and rebuilds the finish on top of it. It removes scratches, gray areas and old stain colour, and it is the only process that resets a floor's appearance completely. It also consumes wear layer, which is why the first question on any refinishing job is how much wood is left.
The full technical detail — method, materials and what decides the outcome — is on our hardwood floor refinishing page.
How to check a flooring contractor in Union City
Ask for the New Jersey home improvement contractor registration number, which begins with the prefix 13VH, and verify it free on the state's public lookup before you sign anything. The status has to read Active: registration expires every 31 March.
New Jersey has no flooring-specific trade licence. HIC registration is the requirement, and state rules put that number on contracts, estimates and advertisements, which makes it checkable before money changes hands.
Beyond registration, the things that actually distinguish crews are checkable too: moisture readings taken before the quote rather than after, a stated grit sequence, and named finish products you can look up a data sheet for.
- 13VH registration number, verified current on the state lookup
- Moisture readings taken and put in writing before quoting
- A stated grit sequence, not just "we sand it"
- Named finish products with published technical data sheets
- EPA Lead-Safe certification if the house predates 1978
- Proof of insurance, with coverage amounts stated
Hardwood Floor Refinishing in towns near Union City
We work Union City and the surrounding Hudson County area. These are the nearest towns we also cover.
Frequently asked questions
Do you serve Union City, NJ?
Yes. Union City is one of the 185 New Jersey municipalities we cover, across nine counties.
How old are most homes in Union City?
The median Union City home was built in 1958, and about 70.2% of the housing stock predates 1978. Figures are from the US Census ACS 2023 5-year estimates.
Does the EPA lead-safe rule apply to my Union City home?
With roughly 70.2% of Union City housing built before 1978, it applies to most addresses here. Your municipal tax record lists your year built, which is what decides it.
Do I need a permit for hardwood floor refinishing in Union City?
Floor refinishing and like-for-like replacement generally do not require a permit in New Jersey. Structural work, subfloor replacement or changes to the building do. Confirm with the Union City construction office for your specific scope.
How far in advance should I book?
It varies with season — heating season and the weeks before holidays are the busiest. Contact us with your timeframe and we will tell you honestly what is available.
What does hardwood floor refinishing cost in Union City?
We do not publish a per-square-foot figure, because the honest number depends on the floor: square footage is only the starting point, and edge work, stairs, closets, coat count, stain and lead-safe requirements all move it. We quote in writing after seeing the floor and taking moisture readings.
Get your Union City floor quoted properly
We take moisture readings and check wear layer before putting a number on the job, so the quote reflects what your floor can actually support — not a rate per square foot applied blind.
Request a free estimate